| |
| |
|
Hardware Information |
|
|
|
Trouble-shooting Hard Drive Problems - Part 1
It is extremely important not to make or write any changes to data on the hard drive without first verifying the hard drive configuration. Therefore, the first priority when unable to access information on a hard drive is to verify all of the configuration information dealing with the suspect hard drive. Partition Parameter
Partition Status
Starting Head
Starting Sector
Starting Cylinder
Partition Type
Ending Head
Ending Sector
Ending Cylinder
Total # of Sectors
Start Absolute Sector
Boot Signature
Step One: Make sure that Micro-Scope detects the hard drive In Micro-Scope, System Configuration, Compare Settings - check to make sure that there is not an asterisk beside the number of hard drives detected value. If there is an asterisk, either the CMOS is set incorrectly, or there is an electronic problem (controller, cable, drive). Step Two: Compare the BIOS parameters against the drive partition information. In Micro-Scope, System Configuration, System Information - note the information displayed for the hard drive, specifically the parameters for the drive in question. Compare these parameters to the parameters in the MBR display under Micro-Scope, System Configuration, Partition Display using the following formula: System Information
Cylinders
Heads
Sectors
If the information does not match, either the partition information is corrupt, or the CMOS setup or controller BIOS setup (if one exists) is incorrect, or there is a problem communicating with the drive. Step Three: Check the drive functionality In Micro-Scope, Diagnostics, Fixed Disk Tests - check the information in the Fixed Disk Selected window. Make sure that the proper drive type, model, and native parameters are showing in this window. If any of the information is incorrect, there is an electronic problem. Check the cable, controller and drive, re-seating all connections, and repeat the above procedure. After correcting the electronic problem, perform a read test on the first 10 cylinders of the drive. If any errors occur, then this is the most likely cause of the drive failure. Perform a read of the entire drive to determine if the errors are electronic in nature, or physical in nature. Electronic problems will result in the errors displayed not always being the same type or in the same location on the drive. If the problem is electronic, replace the cable, controller, and finally drive electronics and repeat the read test until no errors occur. If the error is physical, use an INT 13 type editor (such as Norton Advanced Editor), to block the entire drive and write the information to a daisy chained drive set to the same parameters as the faulty drive. The next step, after the drive passes the read test on the first 10 cylinders, is to check the original partition setup of the drive. Step Four: Check for the physical location of the master boot sector and the volume boot sector. In Micro-Scope, Utilities, Fixed Disk Editor - use the FIND feature to search the last two bytes of each cylinder for a boot signature (55 AA). The first location where a boot signature should be found would be at cylinder 0, head 0, sector 1 (the master boot sector). The second location where a boot signature should be found is at cylinder 0, head 1, sector 1 (the volume boot sector). It is also possible to use the FIND feature to locate the volume boot sector by searching for MSDOS (in DOS based systems) or MSWIN (in Windows95 systems). If there is a duplicate copy of the master boot sector found before the location of the volume boot sector, then it is possible that a boot virus has infected the hard drive in the system. The Rebuild Master Boot feature of Micro-Scope will eliminate any boot sector virus. Be sure to boot the system to the Micro-Scope diskette and immediately do a cold reboot of the system after using the Rebuild Master Boot feature. If the volume boot sector is found in a location other than cylinder 0, head 1, sector 1, count the actual number of sectors before the volume boot sector, and compare that value to the value for the sectors per track displayed in the partition table described in step 2. If the values match, the most likely cause of the system failure is an incorrect CMOS setup. In this case the CMOS needs to be reset to the values indicated by the partition table described in step 2, remembering to use the formula described in step 2 when doing so. If the values do not match, set the CMOS Sectors Per track to the number of sectors counted before the volume boot sector and continue to the next step. Step Five: Check the partition tables to make sure they are correct Reboot the system to Micro-Scope and go to System Configuration, Partition Tables. Check the information displayed in the master boot record to see if there is any obvious corruption (that is, excessively large numbers, all partitions non-bootable, etc.) If there is no obvious corruption in the master boot record, then perform step 2 again. If the information matches at this point, go to step 6. If the information does not match, then set the sectors per track in the Master Boot Record to the number of sectors per track currently set in CMOS, set the starting head to 1, starting sector to 1, and starting cylinder to 0, and write the information to the drive. Step Six: Verify the Master Boot Sector information Display the Volume Boot Sector and use the values for heads and sectors per track (on the right half of the screen) to perform step 2 again. If the values match, then the volume boot sector is probably okay. If any values in the Master Boot Record do not match the table to the right, reset the values to match the values in the table, and write to the drive. If the values still do not match, both the Master Boot Record and the Volume Boot Record are probably corrupt. At this point, e-mail Technical Support for help in this situation. Future articles will provide more insight into the repair procedure. Step Seven: Check the FATs Check to see if the first FAT starts on the sector just beyond the volume boot sector. Use the find feature in the Fixed Disk Editor to search for F8 FF FF in the first three bytes of each sector. The first occurrence should be on sector two of head one. Continue to search until the second FAT is found, indicated by the second occurrence of F8 FF FF. Note the location of the cylinder, head and sector of the second FAT. Based on the start of the second FAT, and the start of the first FAT, calculate how many sectors are in the first FAT. If necessary, read each sector starting at the first sector of the first FAT, keeping a count of the sectors that have been read until F8 FF FF is seen in the upper left of the HEX display, which would indicate the start of the second FAT. After calculating the sectors per FAT, compare this value to the value in the volume boot sector. If the values match, the drive should be accessible through DOS at this point. Step Eight: Attempt to access the drive Boot to a DOS-bootable floppy diskette and attempt to access the drive. If the root directory and sub-directories on the hard drive are readable at this point, then attempt to boot to the drive. If the drive boots at this point, the problem has been corrected. If the drive is still not bootable, e-mail the Micro 2000 Technical Support department for help. Disclaimer - The Micro 2000 Tech Tip is a free service providing information only. While we use reasonable care to see that this information is correct, we do not guarantee it for accuracy, completeness or fitness for a particular purpose. Micro 2000, Inc. shall not be liable for damages of any kind in connection with the use or misuse of this information. Micro 2000 Inc has been helping to solve the day-to-day challenges that IT departments face in order to keep their businesses operational as well as profitable for over 14 years. The company's primary goal is to put the customer first - through feature-rich, simple-to-use IT tools that can help IT administrators manage their jobs more effectively. For more advice and free articles be sure to visit: http://www.micro2000.co.uk
MORE RESOURCES:
Hardware - Google News |
|
|
|
RELATED ARTICLES
Can I Use My Old Ink With My New Printer? The quick answer is.. The Making of Energy Efficient Datacenters The Crooked E: The Unshredded Truth About Enron is a wonderful movie to watch. It is based on the book, The anatomy of greed, written by a former employee of Enron, Brian Cruver. Rackmount Computer Keyboards The other piece of vital equipment to accompany the rack mount computers and the monitors are the rack mount computer keyboards. Rackmount computer keyboards are built with durability and reliability in mind. Throw Away The Fax Machine - A Guide To Online Fax Have you ever felt like throwing the fax machine out the window? Well you may not know it but you can, but not literally please.There have been services available for some time which allow you to take your fax needs online and save yourself the hassle of wrestling with the fax machine. Review of Logitech Computer Speakers When it comes to computer speaker systems, you have a lot of choice. However, there are simply some brands that stand way out in terms of sound quality and dependability, and one of those brands is certainly Logitech. Video Display Video displays are most recent technique used in both outdoor and indoor environments.Video displays are used to display live actions at either sporting event, cultural show, or any industrial event. What You Should Know Before You Buy Computer Equipment You will have many factors to consider when deciding on which computer equipment to buy. The bewildering amount of choices can seem overwhelming. Buying Laser Toner Cartridges Compatible Laser Toner CartridgesRecently, there has been a huge legal and investigative battle with people selling "compatible" laser toner cartridges. Often, a distributor will sell their defective, ineffective, or even damaging laser toner cartridges to unsuspecting resellers. Ergonomic Products 101 Human beings are scaling new heights day by day. Markets are becoming more and more complex and competitive. Thumb Drives - Great New Technology! The ability to easily move data from PC to PC with minimal inconvenience is just another benefit computers have brought to the current business world.Over the past few years, the different options to save and move data have multiplied dramatically. Flyback Transformer-How to Locate the ABL Line Whenever there is a complaint about monitor contrast problem I will check on the flyback transformer ABL (automatic blanking limiter) circuit. Sometimes a weak picture tube might caused contrast problem. Digital Cameras, Media, and Card Readers With the dropping prices on digital cameras and digital media in the past few years there is really a need for a quick reliable transfer method for your pictures to your personal computer.Using the USB cable directly to your camera works to transfer pictures, but it's a waste of your battery and is often quite slow. Video Encryption What is Video Encryption?Video Encryption is an extremely useful method for the stopping unwanted interception and viewing of any transmitted video or other information, for example from a law enforcement video surveillance being relayed back to a central viewing centre.The scrambling is the easy part. Recordable DVD Formats Explained Picking your way through the ton of information available on recordable DVD formats can be a nightmare. To help you out, we've done our best to distill it into this summary. Rear Projection TV Facts - Understanding the Pros & Cons of Rear Projection in the Home Theater Rear Projection Television - An Affordable OptionA great deal of consumer appeal for Rear Projection TV systems arise out of the shear simplicity that this product offers as an immediate solution to getting a bigger TV.No mess, no fuss, if you have the space, either visit your local big screen retailer - or better still, check at your favorite online electronics superstore - to order your product and get it delivered in just a few days; unpack the product and there you have a big screen TV in your living room ready for immediate use!Rear Projection TV Facts:As already stated, rear projection offers a most immediate solution to getting a bigger TV. Expert Guide to DVD Camcorders Thinking about a mini DVD camcorder? You're not alone, it's a rapidly growing sector of the camcorder market, with Hitachi, Sony and Panasonic all making more than one mini dvd camcorder.These camcorders differ from regular digital video cameras in one important way - they record video onto mini DVD discs, rather than DV tape. When Good Color Goes Bad... Even with the popularity of digital technology, and the availability of equipment and software associated with it, many printing firms are still slow to make the changes needed to upgrade their business. More so when it comes to digital photography. Expansion Cards Part 2: AGP Expansion Cards Part 2: AGPThe first in this series of Tech Tips on expansion cards took a look at the PCI slot, and the variety of devices that may find their home in one. Graphics cards are one of the many items that may be used in a PCI slot, but the demands of fast-paced video games require more speed and greater bandwidth than the PCI Bus can provide. Selecting an Ink Jet printer-With Low Operating Cost Printer technology has made tremendous advances in the past five years. Speeds are up and print quality is great. How To Backup Your Hard Drive We all know that we should back up our system as soon as possible. But if you're like most of us, you will get to it tomorrow.
|
| home | site map |
| © 2006 |
